"Gap filler" redirects here. For the Space Shuttle thermal protection system, see Gap fillers. For the car accessory, see Drop Stop.
Platform gap fillers being trialled at Platform 3 of Lo Wu station in Hong Kong in 2009.Carleton station on the Trillium Line is the only station with two platforms. Note gap fillers at solid yellow markings.
Gap fillers close the gap between platform and train cars in the area of doors.
This prevents alighting passengers from accidentally getting stuck in the gap.
There are train-mounted gap fillers, whereas platform gap fillers are movable platform edge extensions installed at subway or railway stations.
Gap fillers are deployed once the train stops but before doors open, and retracted after doors are closed and before the train departs.
Hong Kong
Platform gap fillers were trialled on the platforms of Lo Wu station on the East Rail line in 2009 due to the difficulty of installing platform screen doors on the curved nature of the platforms. They were planned to be installed at other stations along the line along with signal upgrades. However, during the trial period, MTR found that the time taken for the gap filler to fully extend took 15-20 seconds and so greatly increased dwell times of trains. It was decided unsuitable for service. After the trial period ended in October 2009, the platform gap fillers were not used until it was finally removed during a platform-strengthening maintenance operation. Plans to install it on other stations of the East Rail line were also abandoned.
Japan
Some[which?] Japanese railway stations have platform gap fillers, which are known as movable steps (可動ステップ, kadō steppu).[1] Over 200 fillers are used in the Tokyo subway.[2]
London Underground
With the introduction of the NTfL, Transport for London are hoping to introduce platform gap fillers on the Bakerloo, Central & Piccadilly lines (of which 14 platforms have been identified for installation) at curved platforms such as Bank, where the gap between the train and the platform can exceed 1 foot (30.5 cm).[3]
New York City Subway
South Ferry station with gap fillers extended out to a 1 train, as reopened on April 4, 2013.The downtown express track at 14th Street – Union Square. A retracted gap filler can be seen at the bottom of the image along the platform edge, with additional gap fillers visible in the distance.
The Interborough Rapid Transit Company's first cars were built with only two doors on each side, at the extreme ends of the car, lining up with the curved platforms so as not to leave a wide gap between the train and the platform. When the IRT modified existing cars and ordered new cars with a middle door, gap fillers were needed because the middle door was not near the platform. After the City of New York bought the IRT in 1940, new car designs (starting with the R12) had the end doors away from the extreme ends of the car body, which also required the use of gap fillers at certain stations.
Stations equipped
IRT stations with gap fillers are:
South Ferry, outer loop.[4] The station closed on March 16, 2009 and was replaced by a new station which does not require gap fillers. After the latter station was damaged by flooding during Hurricane Sandy, the loop station was reopened as a temporary terminus on April 4, 2013. The 2009-era station reopened on June 27, 2017.
Brooklyn Bridge – City Hall (IRT Lexington Avenue Line) originally had gap fillers on the express platforms. These were deactivated when the station was extended northward. These gap fillers are still in place and can be seen just south of the current platforms.[5]
14th Street – Union Square (IRT Lexington Avenue Line) has gap fillers on both tracks on the downtown platform.[6] There may have been gap fillers on the uptown express platform. A new design of gap filler was installed in 2004 to provide maintenance access from the platform rather than requiring crews to stand at track level.
Times Square (IRT 42nd Street Shuttle) had gap fillers on Shuttle tracks 1 and 3. They were mounted under the platform rather than on it, so they were not ADA accessible.[7] They were removed in 2021 when the station was rebuilt.
Many regional trains in Germany come with platform gap fillers, such as the Bombardier Talent 2.[9] On subway networks, they have also become more common, as evidenced by the Nuremberg U-Bahn whose 1970s first generation VAG Class DT1 do not have them but whose VAG Class DT3 of the 2000s and 2010s and VAG Class G1 of the 2020s come equipped with automatic gap fillers.[10]
Platform gap filler in Airport Rail Link Thailand
Thailand
The Airport Rail Link has installed Platform Gap Fillers at all 8 stations on 12 July 2019 to enhance passenger safety and convenience. These gap fillers bridge the space between the train doors and platforms, providing a safer experience for passengers. The system connects the airport to the city center, with the Platform Gap Fillers made from locally sourced natural rubber, supporting domestic production and ensuring high quality.
USA
Platform Gap Filler installed at The Utah Transit Authority (UTA)
The Utah Transit Authority (UTA) has implemented Platform Gap Filler at various stations throughout the state of Utah. These gap fillers are designed to enhance passenger safety by reducing the gap between train doors and platforms, making boarding and alighting safer and more accessible for all passengers, including those with mobility challenges. The installation of these safety features demonstrates UTA's commitment to improving the overall convenience and safety of its transit services in the region.
