90 mm M1
A 90 mm M1 at CFB Borden
Type	Anti-aircraft gun, anti-tank gun (M1, M2) Tank gun (M3)
Place of origin	United States
Service history
In service	1938–1960[1]
Used by	United States United States Army Canada France[2]
Wars	World War II Korean War
Production history
Produced	1940 -
No. built	133,833 (M1,M2) (1940–1945) 6,648 (M1A1)
Variants	T2 M1 M1A1 M2 T7 M3 M3A1 T8 T15 later redesignated T54 T18–T21
Specifications
Mass	M1A1: 19,000 lb (8,600 kg) M2: 32,300 lb (14,700 kg) M3: 2,260 lb (1,030 kg) (gun only)
Length	M1A1: 29.6 ft (9.0 m)
Barrel length	M1: 200 in (5,100 mm) L/55 (55 caliber) M3: 186 in (4,700 mm) L/53 (53 caliber)
Width	M1A1: 13.6 ft (4.1 m)
Height	M1A1: 10.1 ft (3.1 m)
Crew	M1: 8 (1× gunner 7× loader) M2: 8 (1× gunner 7× loader)
Shell	90 x 600-615mmR M3 HE: 3.5 in × 37.44 in (90 mm × 950 mm) (M71 complete round) M3 APC: 3.5 in × 38.24 in (90 mm × 970 mm) (M82 complete round) M3 AP: 3.5 in × 32.75 in (90 mm × 830 mm) (M77 complete round)
Shell weight	M71 HE: 23.29 lb (10.56 kg) projectile, 41.93 lb (19.02 kg) complete M82 APC: 24.11 lb (10.94 kg) projectile, 42.75 lb (19.39 kg) complete M77 AP: 23.40 lb (10.61 kg) projectile, 42.04 lb (19.07 kg) complete
Caliber	90 mm (3.5 in)
Elevation	M1: -10° to +90° M2: -10° to +90° M3: -10° to +23°
Traverse	360°
Rate of fire	6 rpm in the anti-tank variant 10 rpm in the anti-aircraft variant
Muzzle velocity	M3 HE and AP: 2,700 ft/s (820 m/s) M3 APC: 2,670 ft/s (810 m/s)
Maximum firing range	Maximum horizontal: M1A1: 62,474 ft (19,042 m) Maximum ceiling: M1A1: 43,500 ft (13,300 m)

The 90 mm gun M1/M2/M3 was an American heavy anti-aircraft and anti-tank gun, playing a role similar to the German 8.8cm Flak 18. It had a 3.5 in (90 mm) diameter bore, and a 50 caliber barrel, giving it a length of 15 ft (4.6 m). It was capable of firing a 3.5 in × 23.6 in (90 mm × 600 mm) shell 62,474 ft (19,042 m) horizontally, or a maximum altitude of 43,500 ft (13,300 m).

The 90 mm gun was the US Army's primary heavy anti-aircraft gun from just prior to the opening of World War II into 1946, complemented by small numbers of the much larger 120 mm M1 gun. Both were widely deployed in the United States postwar as the Cold War presented a perceived threat from Soviet bombers. The anti-aircraft guns were phased out in the middle 1950s as their role was taken over by surface-to-air missiles such as the MIM-3 Nike Ajax.^[3]

As a tank gun it was the main weapon of the M36 tank destroyer and M26 Pershing tank, as well as a number of post-war tanks like the M56 Scorpion. It was also briefly deployed from 1943–1946 as a coast defense weapon with the United States Army Coast Artillery Corps. Each gun cost roughly $50,000 to make in 1940 and utilized up to 30 separate contractors to manufacture.^[4]

Prior to World War II, the primary US anti-aircraft guns were the 3-inch M1918 gun (76.2 mm L/40) and 3-inch anti-aircraft gun M3 (76.2 mm L/50), a widely used caliber for this class of weapon. Similar weapons were in British, Soviet and other arsenals. There had been several upgrades to the weapon over its history, including the experimental T8 and T9 versions developed in the early 1930s, that were intended to enter service later in that decade.

However, the US Army became interested in a much more capable weapon instead, and on 9 June 1938, it issued a development contract calling for two new guns, one of 90 mm, which it felt was the largest possible size that was still capable of being manually loaded at high elevations, and another, using assisted loading, of 120 mm (4.7 in). On 18 August 1938 the development of the Mounting T1 was approved as well. The new design seemed so much better than developments of the older three-inch that work on the three-inch T9 was canceled in 1938, just as it became production-ready. On 21 March 1940, the second development of the 90 mm design, the T2, was standardized as the 90 mm M1, while its larger cousin became the 120 mm M1 gun.

A few hundred M1s were completed when several improvements were added to produce the 90 mm M1A1, which entered production in late 1940, and was accepted as the standard on 22 May 1941. Since national arsenals had limited capacity, production of first 300 gun mounts was contracted to Allis-Chalmers in November 1940, with the first unit shipped in September 1941.^[5] The M1A1 included an improved mount and spring-rammer on the breech, with the result that firing rates went up to 20 rounds per minute. Several thousand were available when the US entered the war, and the M1A1 was their standard anti-aircraft gun for the rest of the conflict. Production rates continued to improve, topping out in a few thousand per month.^[when?]

Like the German 88 and the British QF 3.7 inch AA gun, the M1A1 was used against tanks in combat but, unlike the others, it could not be depressed to fire against them. On 11 September 1942, the Army issued specifications for a new mount to allow it to be used in this role, which resulted in the 90 mm M2, introducing yet another new mount, one that could be depressed to 10 degrees below the horizontal and featured a new electrically-assisted rammer. It became the standard weapon from 13 May 1943.

In anti-aircraft use, the guns were normally operated in groups of four, controlled by the M7 or M9 gun director or Kerrison predictors. Radar direction was common, starting with the SCR-268 in 1941, which was not accurate enough to directly lay the guns, but provided accurate ranging throughout the engagement. For night-time use, a searchlight was slaved to the radar with a beam width set so that the target would be somewhere in the beam when it was turned on, at which point the engagement continued as in the day. In 1944, the system was upgraded with the addition of the SCR-584 microwave radar, which was accurate to about 0.06 degrees (1 mil) and also provided automatic tracking. With the SCR-584, direction and range information was sent directly to the Bell Labs M3 gun data computer, and M9 director, which could direct and lay the guns automatically, all the crews had to do was load the guns.

The M3 was also adapted as the main gun for various armored vehicles, starting with the experimental T7 which was accepted as the 90 mm M3. The test firing of the M3 took place on an M10 tank destroyer in early 1943. The M3 gun was used on the M36 tank destroyer, and the T26 (later, M26) Pershing tank.^[7] The M3 fired an M82 APC shot with a muzzle velocity of 2,650 ft/s (810 m/s).^[7] However, both the muzzle velocity of the standard M3 gun and the quality of the steel used in the M82 APC (armor-piercing capped) shot, while comparable to the 8.8 cm KwK 36 L/56 mounted on the Tiger I, were inferior to the Tiger II's KwK 43 L/71 8.8 cm main gun firing its standard APCBC (armor-piercing capped ballistic cap) shot used by German forces, with the result that the former's penetration fell far short of the standard projectile fired by that German tank.^[7] As a result, US ordnance provided some T26/M26 tank crews with the 90 mm HVAP (high-velocity, armor-piercing) tungsten penetrator sub-caliber projectile with a muzzle velocity of 3,350 ft/s (1,020 m/s), or the T33 AP with a re-heat-treated projectile with ballistic windshield and a muzzle velocity of 2,800 ft/s (850 m/s).^[7][8] The HVAP could compete with the KwK 43's penetration performance when firing standard APCBC, but tungsten ammunition was always in short supply.

An unsuccessful anti-tank variant was the T8 gun on the T5 carriage. The gun was an M1 with the recoil mechanism from the M2A1 105 mm howitzer. Eventually a version of the T8 with the T20E1 gun and T15 carriage was tested; this led to the 105 mm anti-tank gun T8.^[10]

Because the standard fifteen-and-a-half foot long M3 90 mm main tank gun proved incapable of penetrating the heaviest frontal armor of the heaviest German tanks such as the Tiger II tank and the rarer Jagdtiger tank destroyer variant, a number of improved versions of the M3 were developed, including the T14 which included a standard muzzle brake and the T15 series.^[7] The 90 mm T15E1 L/73, with its 21 ft (6.4 m) long barrel, was designed and developed as an AT gun that could match or surpass the performance of the 8.8 cm KwK43 L/71 cannon, the famous long 88 on the Tiger II.

The T15 90 mm L/73 anti-tank gun utilized many types of armor piercing ammunition.

• T43 APBC: A solid shot, it was a modified T33 for use by the T15. It had a muzzle velocity of 3,200 ft/s (980 m/s) and therefore increased penetration capabilities. It could punch through 4 in (100 mm) of armor angled at 60°(from vertical) up to about 1,300 ft (400 m).
• T41 APCBC: Modified M82 projectile of the M3 cannon, fired at a much higher velocity of 3,200 ft/s, than the normal 2,670 ft/s. It could defeat up to 8.5 in (220 mm) of vertical armor at 30 ft (9.1 m).
• T44 HVAP: Modified M304(T30E16) for use out of the T15. Muzzle velocity of 3,750 ft/s (1,140 m/s). Maximum penetration of 15 in (380 mm) of vertical armor at 30 ft.
• T50 APCBC: An M82 projectile with increased nose hardness and overall better design. Same muzzle velocity 3,200 ft/s, but increased penetration, equal to the KwK43. 9.1–9.3 in (231–236 mm) against vertical armor at point-blank range.^[11][12]

Two versions of the T15 were made: the T15E1 with single-piece ammunition and the T15E2 with two-piece ammunition.

By mid-March 1945, a T26E1 pilot was equipped with the 90 mm T15E1 and was sent to Europe in a ''trial by combat''. It was given to the 3rd Armor Division where it was enhanced with additional armor plates. Its gun was fired in anger on only one occasion, on 4 April 1945, where it engaged and destroyed a German armored vehicle, probably a Tiger I or Panther, at a range of 4,500 ft (1,400 m) during the fighting along the Weser River.^[13] According to the memoirs of John P. Irwin, it knocked out a King Tiger in Dessau as well as a Panzer IV and a Panther. However, the Tiger II claim is disputed by historians on the grounds that the nearest unit known to be equipped with Tiger IIs was 70 miles from Dessau on the date when the kill was claimed.

Near the end of World War II, more experimental versions of the 90 mm gun were tested including the higher-velocity T18 and T19 main guns. The T19 was a T18 modified in an attempt to reduce barrel wear. Other versions included the T21, which was intended for wheeled vehicles, and the T22, which used the breech from the standard 105 mm M2 howitzer. The T21 and T22 were designed to use larger powder charges. None of these versions entered service.

In the post-World War II era, development of the T15 continued redesignated as the T54, which used a slightly shorter and fatter propellent casing than that of the T15E1.^[14] The T54 served as the main gun on the M26E1 Pershing.^[14]

In 1948 an improved version of the M3A1, designated as the T119, was designed to be used on the T42 (and later M47 Patton) and had a higher muzzle velocity using new ammunition loaded to produce higher chamber pressures. The new ammunition had a slightly longer shoulder to prevent accidental chambering in the older M3 variants. The T119 was backwards compatible with the ammunition used on the M3A1. Upon standardization of the M47 in 1951, the T119E1 version was redesignated as the 90 mm gun M36.^[15]

The lightweight variant of the T119, designated as the T139 and standardized as the 90 mm gun M41, equipped the M48 Patton tanks used in the Vietnam War.^[15] The M41 with a modified recoil system was mounted as the 90 mm gun M54 on the M56 Scorpion anti-tank vehicle. This gun was found to be inadequate and incapable of penetrating modern armor, requiring a stop gap of HEAT-FS shells to be utilized until the 105mm L7 derivative could become more prevalent.

During World War II the Coast Artillery Corps adopted the 90 mm M1 to supplement or replace aging three-inch guns in harbor defense commands in CONUS and US territories. The guns were organized in anti-motor torpedo boat (AMTB) batteries, typically with four 90 mm guns and two 37 mm or 40 mm AA guns each. Typically two of the 90 mm guns were on T3/M3 fixed mounts and two were on towed M1A1 or M2 mounts, with the 37 mm or 40 mm weapons on single towed mounts. The T3/M3 mount was designed for anti-surface or anti-aircraft fire. Emplacements for at least 90 batteries of two fixed guns each, plus mobile weapons, were constructed in CONUS, Panama, Alaska, Hawaii, Puerto Rico, and elsewhere in 1943.^[16]

• Towed anti-aircraft gun. Approved for service in 1940.
• Fixed on T3/M3 mount for coastal artillery service

Towed anti-aircraft gun. Production began in 1940. It featured the M8A1 spring rammer. Its rate of fire was 20 rounds per minute.

A complete redesign to make the gun dual role, functioning as an anti-tank gun as well as an anti-aircraft gun. The ammunition feed was upgraded and an automatic fuze setter-rammer, the M20, was added. This enabled the rate of fire to reach up to 24 rounds per minute. Elevation was improved with the gun able to depress to −10 degrees. To protect the crew, a large metal shield was added. The M2 was the standard weapon by 13 May 1943. From the march it could fire from its wheels in three minutes, and from a fully emplaced position in seven minutes. In 1944 the weapon was enhanced with the addition of proximity fused shells.

A tank-mounted anti-tank version of the gun. It was used to equip the M36 tank destroyer and the M26 Pershing tank. It is also known as the 90 mm L/53.

M3 gun with single baffle muzzle brake and bore evacuator, used on M46 Patton and early versions of the M48 Patton tanks and refurbished M36 tank destroyers during the Korean War.

• M71 HE – 23.29 lb (10.56 kg) (projectile)
• M77 AP – 23.40 lb (10.61 kg) (projectile)
• M82 APC – 24.11 lb (10.94 kg) (projectile)^[17]

• One AAA at Fort Irwin NTC, California, post museum
• One, possibly M1, Travis AFB, Fairfield, California, near the entrance to the skeet range
• One AAA at CFB Borden, Ontario, Canada
• One AAA at Labelle, Quebec, Canada
• One AAA at Sangudo, Alberta, Canada.
• One AAA at Whycocomagh, Nova Scotia, Canada.
• Two AAA at CFB Shilo, Manitoba, Canada, RCA Museum
• One AAA at Shilo, Manitoba, Canada (private collection)
• One AAA at Lemberg, Saskatchewan, Canada (private collection)
• One AAA at Colwood, British Columbia, Canada, Fort Rodd Hill
• One at Savannah, Georgia, National Guard Fairgrounds
• One at Arundel, Quebec, Canada, Legion Hall
• One AAA at Sault Ste. Marie, Ontario, Canada
• One AAA M2 at Fort Sill, Oklahoma, US Army Air Defense Artillery Museum.
• One AAA M1A1 at Fort Sill, Oklahoma, US Army Air Defense Artillery Museum.
• One AAA M2A2 at Fort Sill, Oklahoma, US Army Air Defense Artillery Museum
• One AAA M1A1 at Fort Sill, Oklahoma, 31st ADA Brigade
• One AAA M1A1 at US Veterans Memorial Museum, Huntsville, AL
• One AAA at Broadalbin, New York.
• One AAA at Roswell, New Mexico
• One AAA at Greenville, South Carolina
• One AAA at Anderson, South Carolina, VFW post
• One AAA at Deming, New Mexico, Deming Luna Mimbres Museum
• One AAA at Sainte-Marie-du-Mont, Manche, France, Utah Beach D-Day Museum. This gun belonged to the 116th AAA Gun Battalion and was lost in the Channel 6 June 1944. The gun was recovered by locals after the war.
• One AAA M1A3 (built 1954) at Raton, New Mexico
• One AAA M1A1 at Halifax, Nova Scotia, Royal Artillery Park
• One AAA M1A1 at Fort Bliss, Texas, Fort Bliss Museum
• One AAA M1A1 at Linthicum, Maryland, National Electronics Museum
• Two Anti/Tank T-8 at U.S. Army Armor & Cavalry Collection, Fort Moore, Georgia.
• One M1A3 at Reidsville, Georgia, National Guard Armory
• One M1A3 at Campinas, São Paulo, Brazil, located at an open museum which belongs to the 11ª Brigade of the Brazilian Army
• One seacoast M1 (No. 6931 Chevrolet) on barbette, carriage Model T3, at Battery Parrott, Fort Monroe, Virginia
• One seacoast M1 on barbette, carriage Model T3 (shield scrapped), Eareckson Air Station (formerly Shemya AFB), Shemya, Alaska, outside Bldg 600
• One seacoast on barbette, carriage Model T3, at San Pedro, California, Fort MacArthur Military Museum, (the museum has several barrels and was restoring at least one weapon as of October 2014)
• Two AAA M1A1s in Moscow, Russia, Museum of the Great Patriotic War, supplied as Lend-Lease during WWII
• One 90 mm M2A1 at Tucson, Arizona, Pima Air & Space Museum
• One M1A3 at Historical Military Museum of Cartagena (Spain)
• One at the Kalmthoutse Heide, Belgium
• One at Ft Miles Artillery Museum, Delaware
• One at Mémorial du Débarquement et de la Libération en Provence, Toulon, France

• 184th AAA Battalion (United States)
• Fire-control system
• List of U.S. Army weapons by supply catalog designation
• Rangekeeper
• Seacoast defense in the United States

• 8.8 cm Flak 18/36/37/41: contemporary German anti-aircraft gun
• 8.8 cm KwK 36: contemporary German tank gun, mounted on Tiger I Tanks
• Cannone da 90/53: contemporary Italian anti-aircraft gun
• QF 3.7-inch AA gun: contemporary British anti-aircraft gun, firing a 28 pounds (13 kg) shell
• 85 mm air defense gun M1939 (52-K): contemporary Soviet anti-aircraft gun

• TM 9-2300 standard artillery and fire control material. dated 1944
• TM 9-370
• TM 9-1370
• SNL D-28

Wikimedia Commons has media related to 90 mm gun M1/M2.

• United States War Department TM 9-374 Technical Manual 90-MM Gun M3 Mounted in Combat Vehicles. 11 September 1944
• M3 armor penetration table
• List of all US coastal forts and batteries at the Coastal Defense Study Group, Inc. website
• FortWiki, lists all CONUS and Canadian forts
• "90mm M1A1 & M2 ANTI-AIRCRAFT GUNS". Retrieved 12 July 2017.