A foil is a solid object with a shape such that when placed in a moving fluid at a suitable angle of attack the lift (force generated perpendicular to the fluid flow) is substantially larger than the drag (force generated parallel to the fluid flow). If the fluid is a gas, the foil is called an airfoil or aerofoil, and if the fluid is water the foil is called a hydrofoil.
Physics of foils
Streamlines around a NACA 0012 airfoil at moderate angle of attack
A foil generates lift primarily because of its shape and angle of attack. When oriented at a suitable angle, the foil deflects the oncoming fluid, resulting in a force on the foil in the direction opposite to the deflection. This force can be resolved into two components: lift and drag. This "turning" of the fluid in the vicinity of the foil creates curved streamlines which results in lower pressure on one side and higher pressure on the other. This pressure difference is accompanied by a velocity difference, via Bernoulli's principle, so for foils generating lift the resulting flowfield about the foil has a higher average velocity on one surface than on the other.[1][2][3][4]
A more detailed description of the flowfield is given by the simplified Navier–Stokes equations, applicable when the fluid is incompressible. And since the effects of the compressibility of air at low speeds is negligible, these simplified equations can be used for airfoils as long as the airflow is substantially less than the speed of sound (up to about Mach 0.3).[5][6] For hydrofoils at high speeds, of the order of 50 knots (26 m/s) according to Faltinsen,[7]cavitation and ventilation – with air penetrating along the strut from the water surface to the foil – may occur. Both effects may have a substantial influence on the foil's lift.
Basic design considerations
The simplest type of foil is a flat plate. When set at an angle (the angle of attack) to the flow the plate will deflect the fluid passing over and under it, and this deflection will result in a lift force on the plate. However, while it does generate lift, it also generates a large amount of drag.[8]
Since even a flat plate can generate lift, a significant factor in foil design is the minimization of drag. An example of this is the rudder of a boat or aircraft. When designing a rudder a key design factor is the minimization of drag in its neutral position, which is balanced with the need to produce sufficient lift with which to turn the craft at a reasonable rate.
[9]
The weight a foil can lift is proportional to its lift coefficient, the density of the fluid, the foil area and its speed squared. The following shows the lifting ability of a flat plate with span 10 metres and area 10 square metres moving at a speed of 10 m/s at different altitudes and water depths. It uses the lift at an altitude of 11 km as a datum to show how the lift increases with decreasing altitude (increasing air density). It also shows the influence of ground effect and then the effect of increase in density going from air to water.[10]
height 11 km: lift 1.0 (datum for comparison)
5 m 3.4
in ground effect 4.1
water surface-planing 1,280
just submerged 1,420
depth 5 m 2,840
10 km 2,860
^"...the effect of the wing is to give the air stream a downward velocity component. The reaction force of the deflected air mass must then act on the wing to give it an equal and opposite upward component." In: Halliday, David; Resnick, Robert, Fundamentals of Physics 3rd Edition, John Wiley & Sons, p. 378
^"If the body is shaped, moved, or inclined in such a way as to produce a net deflection or turning of the flow, the local velocity is changed in magnitude, direction, or both. Changing the velocity creates a net force on the body" "Lift from Flow Turning". NASA Glenn Research Center. Archived from the original on 2011-07-05. Retrieved 2011-06-29.
^"The cause of the aerodynamic lifting force is the downward acceleration of air by the airfoil..." Weltner, Klaus; Ingelman-Sundberg, Martin, Physics of Flight - reviewed, archived from the original on 2011-07-19
^"...the motion of objects in air and in water obeys identical laws until their speed approaches the speed of sound."(page 41) "... air too can be regarded as incompressible as long as flow speeds remain reasonably low. This assumption is roughly valid as long as airplanes fly slower than... about one-third of the speed of sound."(page 61) What Makes Airplanes Fly? Wegener, Peter P. Springer-Verlag 1991 ISBN0-387-97513-6
^"...the low-speed flow of air, where V < 100 m/s (or V < 225 mi/hr) can also be assumed to be incompressible to a close approximation." in Anderson, John D. Jr. Introduction to Flight 4th ed McGraw-Hill 2000 ISBN0-07-109282-X pg 114
